Helmets

Are you heading out for a cruise about town? Well, don't forget your Cruz. The Cruz is the perfect protection for your daily commute, a run to the farmers market, or for just a jaunt around the neighborhood. Get your Cruz on. - Snap-Fit Removable Visor - Kalilight rear flashing light Material: - Bamboo fabric pad - 100% recycled plastic visor - Recycled EPS Straps - Recycled EPS foam Certifications: - CPSC - EN 1078 Sizing: - Small/Medium = 55 – 61cm - Large/X-Large = 60 – 63cm

Strap divider for thick Lazer helmet straps COMPATIBILITY - Blade+ MIPS - Blade+ - Tonic MIPS - Tonic - Coyote MIPS - Coyote - Chiru - Next+ - Cameleon MIPS - Compact DLX MIPS - Compact DLX - Compact - J1 - Gekko MIPS - Gekko - Lil'Gekko MIPS - Lil'Gekko - ATTACHMENT: strap - WEIGHT: 3g - MATERIAL: Nylon

Strap divider for thin Lazer helmet straps COMPATIBILITY - Bullet 2.0 - G1 MIPS - G1 - Z1 MIPS - Z1 - Century MIPS - Century - Victor - Wasp Air Tri - Impala - ATTACHMENT: strap - WEIGHT: 3g - MATERIAL: Nylon

- Made in the USA - Enables Take a Look Original Eyeglass Mirror to fit helmets - Does not work with Take a Look Compact Eyeglass Mirror

Buckle for thick Lazer helmet straps. COMPATIBILITY: - Blade+ MIPS - Blade+ - Tonic MIPS - Tonic - Coyote MIPS - Coyote - Chiru - Next+ - Cameleon MIPS - Compact DLX MIPS - Compact DLX - Compact - J1 - Gekko MIPS - Gekko - Lil'Gekko MIPS - Lil'Gekko - ATTACHMENT: strap - WEIGHT: 5g - MATERIAL: Nylon

Compatible with Shiner and Shiner Back lights - Rubber pad with loop straps to quickly mount and remove light for recharging - 50mm bolt spacing to fit most rear racks

Replacement Pads for Lazer's BOB Helmet

Screws for Impala visor. - COMPATIBILITY: Impala MIPS, Impala - WEIGHT: 1g - MATERIAL: Aluminum

Freshen up the interior of your helmet with a new pad set! - Replacement pads for Jackal helmets

Screws for Jackal Visor

Visor Screw Set for Blade Helmet.

Freshen up the interior of your helmet with a new pad set! Padset details listed below. Replacement padset for Lazer Bullet and Bullet MIPS helmets. Set includes six pads - Two front pads, two top center pads, two top side pads. - COMPATIBILITY: Bullet, Bullet 2.0 - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

Camera mount for Jackal and Impala helmets. - COMPATIBILITY: Jackal MIPS, Jackal, Impala MIPS, Impala - ATTACHMENT: Velcro - WEIGHT: 13g - MATERIAL: Nylon

Freshen up the interior of your helmet with a new pad set! Padset details listed below. Replacement padset for Lazer Cameleon MIPS helmet. Set includes four pads - front pad, two top side pads and top center pad. - COMPATIBILITY: Cameleon MIPS - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

Freshen up the interior of your helmet with a new pad set! Padset details listed below. Replacement padset for Lazer Coyote and Coyote MIPS helmets. Set includes three pads - One front/top pad and two top side pads. - COMPATIBILITY: Coyote MIPS, Coyote - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

Freshen up the interior of your helmet with a new pad set! Replacement padset for Lazer Urbanize MIPS helmets. Set includes two pads - one front pad and one top center pad COMPATIBILITY - Urbanize MIPS - ATTACHMENT: velcro - WEIGHT: 12g - MATERIAL: Foam

- Replacement X-Static pads for Lazer's Wasp Air Helmet - X-Static pads are an anti-microbial, self-cleaning pad system

This helmet mount works with all CatEye Lights. Pair it with the Volt 800 for the ultimate trail solution.

A helmet-mounted taillight is an ideal way to help make sure you are seen in low light conditions. The ATS LED Taillight only fits Lazer helmets equipped with the Advanced Turnfit System. - COMPATIBILITY: Bullet 2.0, Century MIPS, Century, Wasp Air Tri, Victor, Impala MIPS, Impala, Urbanize MIPS - BATTERY TYPE: LR41 button battery - RUN TIME: 37 hours - LUMENS: 4 lumens - ATTACHMENT: ATS dial - WEIGHT: 15g - MATERIAL: Nylon

Visor for Impala helmet COMPATIBILITY - Impala MIPS - Impala - ATTACHMENT: Direct Mount - WEIGHT: 45g - MATERIAL: Nylon

- Replacement padding for Kickstart and Kickstart Lite

Handlebar mount for Lumos remote

- Replacement padding for Lumos Matrix and Street helmets

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally, the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. - COMPATIBILITY: Blade+ MIPS, Blade+, Blade, Blade MIPS - ATTACHMENT: Blade or Blade+ helmet - WEIGHT: 45g - MATERIAL: Polycarbonate

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. Sizing: - Small = 52 – 56cm - Medium = 55 – 59cm - Large = 58 – 61cm

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride.

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally, the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. - COMPATIBILITY: G1 MIPS, G1 - ATTACHMENT: G1 helmet - WEIGHT: 45g - MATERIAL: Polycarbonate

Keep the rain, snow and mud from getting inside your helmet, or use as a quick aerodynamic solution to close off the front and side vents. Aeroshell is a great accessory for compatible Lazer helmets! The Aeroshell is a plastic cover, designed to fit perfectly over specific models of Lazer helmets. The Aeroshell snaps into place and protects the riders head from wind and rain while still allowing for some air movement under the front of the helmet and out the rear vents. The Aeroshell is unique in that it is easily removed from the helmet when riding conditions are such that additional ventilation is desired. Snap it on when the rain is pouring down and pull it off when the sun starts to shine, the Aeroshell is the perfect tool for every possible condition. Additionally, the Aeroshell provides a significant increase in Aerodynamic performance once it is installed on the helmet. By closing off the ventilation holes, the amount of aerodynamic drag the helmet creates is strongly reduced, making your road helmet into an aero helmet and resulting in a faster ride. - COMPATIBILITY: Z1 MIPS, Z1 - ATTACHMENT: Z1 helmet - WEIGHT: 45g - MATERIAL: Polycarbonate

Liner and cheek pads for Backflip Helmet.

The Asteroid fits all new and older Bern helmets with a two-hole mount located in the rear of the shell. USB rechargeable. - 12 Lumens - Micro USB rechargeable - 3 Light Modes (Flash 24 hours, Pulse 6.5 hours, Steady 5.5 hours) - Water Resistant - 16 grams - 26mm tall, 39mm wide, 20mm thick (w/o bracket)